1. ___________ is the confirmation of the product to the accepted level of standards set by standardization organization, buyer or the consumer
Correct : A. Quality
2. __________is an example for extrinsic cue of quality
Correct : A. Price
3. __________ is created during product manufacturing, is dependent on styling, fit, materials and assembly methods
Correct : A. Intrinsic quality
4. Visual merchandising techniques and advertising are common ______________
Correct : B. Extrinsic cue
5. _______________ has been considered as a combination of various process representing dynamic behavior of an organization
Correct : A. TQM
6. ___________ is the model for quality assurance in design and development, production installation and servicing
Correct : C. ISO9001
7. _________ is the model for quality assurance in production installation and servicing
Correct : C. ISO 9002
8. _________ is the model for quality assurance in final inspection and Test
Correct : C. ISO 9003
9. __________ is a guide for application of quality management system
Correct : D. ISO 9004
10. Expand ISO
Correct : D. International Standard organization
11. __________ can be considered as a high level audit performed at management level and take place at regular interval
Correct : D. Quality monitor
12. __________ is an inbuilt function for majority of clothing industry
Correct : A. Quality control
13. _____________ define the quality as the degree to which a set of inherent characteristic fulfills requirements
Correct : A. ISO
14. SQC is ______________
Correct : A. Statistical quality control
15. SQC was introduced in___________________
Correct : A. 1924
16. ______________provides managers and technologists with regular and uptodate feedback regarding the overall effectiveness of their own sphere of operation
Correct : D. Quality monitor
17. CMT is _____________
Correct : A. Cut make trim
18. _______________denotes non conformance , unperfection in an entity
Correct : D. Defect
19. ________________is a defect that is not likely to reduce materially the usability of the unit of product for its intended purpose
Correct : D. Minor defect
20. __________is a defect, other than critical, that is likely to result in failure or to reduce materially the usability of the product for its intended purpose
Correct : D. Major defect
21. _____________is a defect that judgment and experience indicate is likely to result in hazardous or unsafe condition for individuals, using, maintaining or depending upon the product
Correct : D. critical defect
22. _____________ is the maximum allowable percent defective, for sampling inspection purpose can be considered satisfactory as a process average
Correct : A. AQL
23. The width of fabric in inches is called as _____________
Correct : A. Dia
24. ______________denotes dimensional stability
Correct : D. shrinkage
25. _____________ is grams per square meter
Correct : A. GSM
26. Tolerance level in case of GSM is______________
Correct : A. + or -5 gms
27. The load or force required for breaking the material
Correct : B. Breaking strength
28. Loss of color from a dyed fabric occurred when immersed in water, dry cleaning solvent or other liquid medium
Correct : A. Color bleading
29. The dried color transfer from a colored fabric to another surface by abrasive action is called as _________
Correct : C. Crocking
30. Crinckled effect found along the seam of a garment due to differential stretch properties of two different fabric is called as _________
Correct : A. Puckering
31. Small fiber balls are formed on the surface of fabric due to abrasion action
Correct : A. Pilling
32. __________ occurs due to lose stitch density
Correct : A. Grin seam
33. _________ is a knitting defect due to excessive thickness of yarn
Correct : D. Batching up
34. The color smeared out during printing is called as ______
Correct : A. Color smear
35. __________ is the test that is of use with knitted fabrics to determine its strength
Correct : B. Bursting strength
36. Inspection done in between any operation and a process is known as
Correct : A. Inproinspection
37. _________ is done in inspection center(IC) due to excessive defect percentage in the already inspected lot
Correct : A. 100% inspection
38. ___________ inspection is done prior to final inspection
Correct : A. Pre final inspection
39. _________ are the tiny holes that appear after rectification or rework of the defective portion of a garment
Correct : A. Needle hole
40. The color printed not in a proper position during printing is called as ___________
Correct : B. Out of register
41. The printing pattern is broken due to crease in fabric during printing __________
Correct : A. Scrimp
42. The lack of affinity to dyes at particular portions of fabric will result in _______________
Correct : B. Patches
43. _______________is the pre production process of separating(sectioning, carving) a spread into garment parts that are precise size and shapes of pattern pieces on a marker
Correct : A. Cutting
44. ___________cutting is the most effective with harder sheet materials, including leather and plastics
Correct : C. Water jet cutting
45. In the case of _____________cutting machine, in several plies are cut , the accuracy is not perfect as it is a V cut rather than straight line
Correct : A. Laser cutting
46. Variation that exceeds tolerances or donot meet specifications are called ___________
Correct : C. Defects
47. _____________defects prevents usability of performance
Correct : B. Critical
48. _________may effect usability or interfere with performance
Correct : C. Major defect
49. ______________defect will not effect usability
Correct : D. Minor defect
50. If the quality of a garment is evaluated as a acceptable it is_________
Correct : D. First quality
51. `______________are evaluated as seconds,thirds,irregulars or scrap depending on the number and type of defects
Correct : A. Defectives
52. Expand QA.
Correct : B. Quality assurance
53. Expand QC.
Correct : C. Quality control
54. _____________are a set of characteristics or procedures that provide a basis for resource and production decisions
Correct : A. Quality standards
55. ______________reflects the overall quality and performance levels the firm seeks to achieve
Correct : A. Standards
56. _________are visible variation in fabric such as shading and fabric flaws
Correct : A. Patent defects
57. _____________ can be readily seen or detected
Correct : A. Patent defects
58. Patent defect and latent defect are two general types of ______________ problems
Correct : A. Fabric
59. _____________ is an example for patent defect
Correct : A. Bow and skew
60. Streaks, stains and slubs are _____________
Correct : C. Patent defect
61. _____________ cannot be detected by simply viewing the fabric
Correct : D. Latent defects
62. The defect that appear after the fabric has been subjected to processes such as steaming , wet processing or pressing is known as
Correct : C. Latent defect
63. Shrinkage or stretching are common _____________-
Correct : A. Latent defect
64. ___________ is an example for latent defect
Correct : A. Lack of color fastness
65. ______ is variation in hue , value, or intensity measured against a standard
Correct : A. Shading
66. ______________include knots,stains,broken warp and filling yarns, holes and like that occur by accident during fabric production
Correct : B. Fabric flaws
67. _______________is a bar or striped effect, usually in the filling direction, creating a difference in color or shade, may be caused irregularities in fiber or yarn processing
Correct : C. Barre and streaks
68. ______________is variation in crosswise dimensions of fabric because of relaxation, tension, or application of water, heat, steam, laundry or dry cleaning
Correct : B. Width variation
69. Distortion in wrap and filling alignment caused by in proper tensioning of fabric in weaving, knitting or finishing is known as _________
Correct : A. Bow and skew
70. Uneven edges because of poor tension, entering or handling during finishing
Correct : A. Wavy selvages
71. ____________________ is a system for measuring and checking and then incorporates a feedback mechanism to explore the causes of poor quality and take corrective steps
Correct : A. Control
72. ______________________is a quality control system employing the statistical techniques to control quality by performing inspection, testing and analyze to conclude whether the quality of a product is as per laid quality standards
Correct : D. SQC
73. ______________is established by authority as a model or example to be followed
Correct : D. Standard
74. ___________________facilitate communication and prevent misunderstanding
Correct : D. Standard
75. ________________among the following is not a standard test method for garment industries as well as for all textiles
Correct : B. TQM
76. Which among the following is a source of standard test method for garment industries as well as for all textiles
Correct : C. BIS
77. ANSI stands for
Correct : A. American National Standards Institute
78. Bs stands for
Correct : C. British standards
79. BIS stands for
Correct : B. Bureau of Indian standard
80. AATCC stands for
Correct : A. American association for textile chemist and colonist
81. __________________is an embodiment of design and properties of a product or service which ensures customers satisfactions
Correct : A. Quality
82. A manufacturer remains in business only as long as his product quality satisfies his
Correct : B. Customers
83. Faults are written down and recorded on a fault analysis card or chart known as
Correct : A. FACERAP cards
84. _______________faults are those resulting from machine or operative defects
Correct : B. General faults
85. ______________faults are those which occur specifically in the job being studied
Correct : C. Job
86. __________________is an example for general fault
Correct : B. Careless handling
87. Incorrect threading is an example for ______________
Correct : A. General fault
88. _____________________is an example for general fault
Correct : B. Slipped stitches
89. Step joints are example for_____________
Correct : C. Job fault
90. Wrong measurement are example for___________________
Correct : A. Job fault
91. ________________is defined as anything potentially harmful to the product user
Correct : A. Critical defect
92. ________________is to check beginning with knitting and weaving then to raw materials marker layout, spreading, cutting, sewing, wet processing, screen printing and other embellishments
Correct : B. In process inspection
93. ___________________is to determine the quality of an order by its visual appearance, measurement to specifications and packing execution, and will be performed before the finished product is shipped
Correct : D. Shipment inspection
94. ____________________deals with the planning the activities to meet the customer needs
Correct : B. Quality planning
95. ________________deals with monitoring the activities using different control points and checks to ensure bad quality does not go to the customer
Correct : A. Quality control
96. __________________is focused on establishing systems and procedures to ensure that quality is achieved all the time
Correct : C. Quality assurance
97. __________________concentrates on changing needs of the customer and proactively works for improving the levels of quality
Correct : D. Quality improvement
98. Quality ___________ is a process of planning the production activities in order to achieve the goals of meeting the customer requirements in time within the available resources
Correct : A. planning
99. _________ is the system for ensuring maintenance of proper standard in manufactured goods especially by periodic random inspection of the product
Correct : B. Quality control
100. A system for achieving or maintaining the desired level of quality in a manufactured product by inspecting samples and assessing what changes may be needed in the manufacturing process